Menu

Topics

© 2012 BlogName - All rights reserved.

Firstyme WordPress Theme.
Designed by Charlie Asemota.

Input Shaft early Chevy NP241

December 11, 2014 - Author: bartbarton

 

Question:  I am looking for an input shaft to convert an np241cearly Chevy 241 to a dodge 29 spline input. All the 29 spline shafts I can find are specified for the 94+ t-cases. Do you have anything that will work with a 1989 model year Chevy t-case?

Answer:   We can supply an input shaft that will work in the early planetary but you will need to change the input bearing also… priced below

This input will fit and work fine in your pre 1994 unit

Shaft Input 29 Spline 6010N Bearing Narrow part number NP4797029-R your cost $122.92

Input Bearing .630 inches wide part number MWT6010-N your cost is $20.66 plus shipping.

Plus Shipping and Handling, give Scott or Chris a call 888-824-2012 they can help you.  See the other parts we can supply for NP241 transfer cases on our site.

No Comments - Categories: NP241 Transfer Case

Chevrolet NP241C Parts Required

December 10, 2014 - Author: bartbarton

I have a Chevy pickup 4WD with NP241np241c

Question:   I’m looking for some seals for my NP241C transfer case, Assembly Number: 1562 4672, Serial Number: 3 11 89 2.  I need parts from this picture: http://www.drivetrain.com/images/stories/product_imgs_large/np241_lg.jpg  1, 2, 13, 37, 42, 49, 50, 56 and 72. Are you able to supply them?

Answer:   We can provide the following parts for your Chevrolet NP241C transfer Case repair:

  • Extension Housing Bushing 2.010 inch OD 32 Spline Output Slip yoke type part number MWT100408 your cost $10.00
  • Planet Thrust Washer Plastic part number MWT4338908 your cost $4.00 each, there are two thrust washers one on each side of the input
  • Range Fork Cast #17833 driver side Front Output Aluminum part number MWTNV17833 your cost $35.00, #56, #49 and #50 are replaced with the updated range fork.
  • Fork insert 2 required part number MWTNP4167869 your cost $1.00 each.
  • Other pad is part number NP4338376 your cost $1.00
  • Everything else in the list is in the gasket and seal kit part number TSK208 your cost is $28.21 plus freight.

Give Scott a call toll free 888-824 2012 he can help. You can see the other NP241C parts we can supply on our web site.

 

 

No Comments - Categories: NP241 Transfer Case

NP231 Rebuild Kit

December 1, 2014 - Author: bartbarton

I have a Dodge Ram 1500 1996 5.9lt 4WD

Question:  I’m looking for an NP231_TCCRY011overhaul kit for my NP231-D transfer case:

Answer:   The correct part number for the bearing rebuild kit is MWTK231A your cost is $90.52, we would suggest that you inspect the chain it’s our experience that the chain should also be replaced. The chain part number is MWTCL10-022 your ost $96.00 plus freight.

Give Scott a call toll free 888-824-2012 he can help you with the technical aspects of the overhaul as well as get you the correct parts.  You can see the other parts that we can supply for the NP231 on our site.

No Comments - Categories: NP231 Transfer Case, Uncategorized

Explorer 1997 BW4405 Transfer Case

November 11, 2014 - Author: bartbarton

I have a 1997 Ford Explorer 4.0L 4WD

Question:   I have some transfer case issues with my trick. I have a BW 4405 which started to make the grinding noise when foot is lifted off the accelerator over 50mph, the nose stops under 50mph or when the rpm is above 1500rpm ish I have removed the transfer case and found 2 of the balls on the electromagnetic clutch have shattered also the White plastic thrust washer is also mis-shapen and requires to be replaced Can you supply these parts and gaskets to the UK and also if there is anything you feel I should get or advice that would be appreciated.

Answer:   You may need the following parts:

We can supply the 3 balls $2.00 each

Nylon isolator washer $5.00 plus shipping and handling.

There are a couple other things that may be the problem with the BW4405 if you were having disengagement issues..

The shim between the rear case ant the back of the rear output bearing. The shift ca will be worn on the top of the slot all the way at the bottom, if that’s the case you will need the following parts:

  • Drawing Item 645B Range Slider part number MWT1354-089-001 your cost $60.00
  • Shim Kit, Rear Case TRS334206K your cost is $7.25
  • Drawing Item 626E Electric Shift Cam (Range Fork) part number TRS345626 your cost is $24/94

Need additional parts for your BW4405 see our web site.

If you need additional information give Scott a call toll free 888-824-2012 he can help you.

No Comments - Categories: BW4405 Transfer Case

2003 Yukon Transfer Case Problem

October 15, 2014 - Author: bartbarton

I have a Yukon XL 5.3L

Question:  Im having problems with low speed turns and wheel binding both forward and reverse. The rear wheels are the ones scuffing. The transfer case is a NR4 according to the sticker in the glove box.I have placed the transfer case in the neutral towing mode and coasted down a incline. when the wheels were turned to either side the vehicle slowed as if the brakes were being applied . when I am in 4LOW it is not as bad as 4HI. I want to fix the truck and realize its either the TC of the rear diff just looking for a direction.

Answer:   Sounds like it is a transfer case problem….

This is a BW4484 transfer case that has a differential assembly in it I assume there is an issue with the pinion gears binding in the transfer case and as long as all 4 wheels are turning and there is not an actuator on the front diff to disconnect it will bind even in (N)

We recommend you drain the fluid and look for metal particles/chunks, to be sure and this should give you a pretty good indication on what’s going on.

We can provide a rebuilt transfer case it our part number TCGM048 your cost is $1460.00 exchange with a $350 core charge plus freight.

Once you get a look at the fluid give Scott a call toll free 888-824-2012 he can help you.

No Comments - Categories: Transfer Case

F150 Transmission Conversion

September 22, 2014 - Author: bartbarton

I have a F150 1995 4WD 300

Question:  I have a 95 f150 with a inline 6 5 speed and a Borg Warner 1356 Transfer Case I going to do a engine swap for 302 and an aod transmission is my transfer case going to fit on the aod tranny?

Answer:  Yes the BW1356  will fit just fine, you can see the other parts we can provide for the BW1356 on our site.

No Comments - Categories: Transfer Case

Need Stronger NP205 Transfer Case

September 2, 2014 - Author: bartbarton

I have a 1977 Ford 3/4 ton 4WD

Question:  I am looking for a stronger built NP 205 divorced transfer case. Do you make a stronger than stock case? How much are they? I don’t have a core to return.

Answer:

We can build with a cryo treated input, front and rear outputs np205_transfercasea rebuilt  unit.

Your cost is $895.00 exchange $250 core charge plus freight.

Give Scott a call toll free 888-824-2012 he can help you.

 

No Comments - Categories: Transfer Case

Denali 2007 making clunk, clunk sound?

August 27, 2014 - Author: bartbarton

I have a Denali 2007 6.2L engine with Automatic transmission 4WD

Question:  I have this Denali, BW4485and it is making a loud clunk, clunk, clunk…sound when under harder acceleration. It was suggested that I need to do a master rebuild kit to fix the problem. Would that be your suggestion, or do you suggest just buying a rebuilt transfer case from you to bolt in. The vehicle has 160k on it now. I’m willing to pay a little more for convenience, but I don’t want to spend $1600 if a simple $200 rebuild kit would work.

Answer:   This is a BW4485 transfer case, the problem you describe could be a problem with stretched or worn out chain.   We would suggest you rebuild the unit and purchase the following parts:

  • Bearing Overhaul Kit part number TRSBKBK4485 your cost $123.93
  • Chain part number MTCCL10-502 is the transfer case chain  your cost $140.00 plus freight.

Give Scott a call toll free 888-824-2012 he can help you.  You can see the other parts we can supply for your BW4485 on our web site.

 

No Comments - Categories: Transfer Case

Transfer Case Mercedes 2007 Replacement

August 20, 2014 - Author: bartbarton

I have a Mercedes Benz Model C280 4 matic 2007.

Question:  I need a quotation for a remanufactured transfer case 4Matic, MB#203-280-07-99, including price, shipping charges to zip code 53705 and warranty.

Answer:  We can provide a rebuilt unit with all new bearings, gaskets, seals and chain your cost is $1750 exchange with $250 core deposit.  Shipping for outbound of rebuilt unit and return of your core is $120.00.  This unit will have a one year warranty.

If you need additional technical information give Scott a call at 888-824-2012 he can help you.

No Comments - Categories: Transfer Case

Clunking Sound NP233 Blazer 1996

August 18, 2014 - Author: bartbarton

I have a Blazer 1996 with 4.3L 4WD.

Question:  I have a question np233_transfer_case_imageI REALLY hope you can help me out with, I have a 96 Chevy s10 blazer 4wd, It has the np233 transfer case. There is slack in the drive shaft so me and my dad checked it thinking u joints but when you grab the drive shaft and shake it the clanking sounds like its coming from the transfer case or transmission? Dad is thinking transfer case any thoughts?

Answer:  We would suggest you start by checking the fluid level and condition of the transfer case and rear differentials fluids, drain and inspect.

Which shaft are you turning to produce this noise, front or rear. Worn spider/side gears in the differential can also produce this problem.

You should be able to tell a lot by the fluid level and condition of the fluids, look for chunks, pieces and sliver nuggets.

If the transfer case is sloppy or the culprit we recommend the following parts:

  • NP233 16mm wide input bearing rebuild kit our part number TRSBK230 your cost $70.00
  • Chain 1.25 inch wide 31 links part number TRSHV022 your cost $96.00.

Need more help with diagnostics or more parts give Scott a call 888-824-2012 he can help you.

No Comments - Categories: Transfer Case